Carbon Fiber Vinyl Decal Hood Wrap for Dodge RAM 1500 Laramie Longhorn 2019-2020

Carbon Fiber Vinyl Decal Hood Wrap for Dodge RAM 1500 Laramie Longhorn 2019-2020
Carbon Fiber Vinyl Decal Hood Wrap for Dodge RAM 1500 Laramie Longhorn 2019-2020
Carbon Fiber Vinyl Decal Hood Wrap for Dodge RAM 1500 Laramie Longhorn 2019-2020

Carbon Fiber Vinyl Decal Hood Wrap for Dodge RAM 1500 Laramie Longhorn 2019-2020

Highly conformable and great cold stretch, better than 3M Wrap Film Series 1080. Use it right out of the box, no need to print or apply an overlaminate.

3M Wrap Film Series 2080 in gloss colors comes with a Protective Film Layer, which can be removed quickly, easily and cleanly after install, reducing surface impressions and scratches for a beautiful finish. Excellent slideability and initial tack for easy snap-up, but reliable tack during installation.

Non-visible air release channels with excellent air flow to prevent bubbles. The gloss colored films also come with a protective film layer to reduce surface impressions and scratches.

It can remain on the wrap film throughout the installation process, and then removed easily. The 60 inch width allows you to wrap almost any section of a vehicle without seams. Cleaning the Vehicle Properly Before Applying Film. Cleaning the application surface properly is one of the most important steps to a good application. Wash and dry the vehicle thoroughly.

Wipe the application area and a large area around it with a solvent-based cleaner, wiping dry as you work. Wipe again with a 2:1 mixture of Isopropyl Alcohol (IPA) and water, wiping dry as you work. For complete details, please read 3M Instruction Bulletin 5.36.

Alternatively, use 3M Surface Preparation System and lint-free paper towels for cleaning the application surface. After cleaning make sure that the application surface is completely dry.

Using Masking Tape for Alignment. Always use masking tape to mark alignment. Do not use a grease pencil. Its waxy core can become embedded in the films texture, and.

Attempting to remove it may damage the texture. Covering the Edge of the Squeegee to Reduce Scratches. 3M recommends using a high-density felt squeegee, or covering the edge of a 3M Applicator PA1-G (gold) with the loop side of 3M Scotchmate Reclosable Hook and Loop Fastener - Loop portion SJ-35231 or PTFE tape. Another option is to use a squeegee with a suede or nylon wrapped edge. Alternatively, use 3M Application PA1-G (gold) squeegee with thin, soft micro fiber sleeves. Using a Heat Gun, Not a Torch, for Heating the Film.

Heat the film only with a heat gun - never a torch. A torch is likely to alter the appearance of the finish permanently, which cannot be repaired. 3M offers several roller based tools to help get the job done.

3M Rapid Roller Applicator CPA-2 is for flat areas, such as the hood or roof. 3M Roller L, 3M Roller S and 3M Vehicle Channel Applicator Tool VCAT-2 have specially shaped rollers to help conform heated film into channels and recesses.

Read more about these tools in 3M Instruction Bulletin 5.36. Film series 2080 features a dual cast construction that is 3.5 mil thick.

It has just enough rigidity to allow easy installation without an. Due to the films texture, application tape may not work well with cut and prespaced graphics. Wrap shops may choose to test and approve an application tape. 3M Prespacing Tape SCPS-55 is a good one to try.

The item "Carbon Fiber Vinyl Decal Hood Wrap for Dodge RAM 1500 Laramie Longhorn 2019-2020" is in sale since Tuesday, April 6, 2021. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Decals/Emblems/License Frames\Decals & Stickers\Graphics Decals". The seller is "factory-crafts" and is located in Las Vegas, Nevada. This item can be shipped worldwide.


Carbon Fiber Vinyl Decal Hood Wrap for Dodge RAM 1500 Laramie Longhorn 2019-2020


Dodge Ram Fiber    Links    Contact Us    Privacy Policy Agreement    Service Agreement